5.5KW Inverter Motor Drives Low Voltage 380v Frequency Inverter
ZONCN Z2000 Frequency Inverter AC drives 5.5KW
Basic product introduction:
· Senseless flux vector control(VC)V/F(Voltage/Frequency)control
· The overload capacity allows for 60 seconds at 150% of the rated current and 3 seconds at 180% of the rated current.
· Ten auxiliary frequency sources are available.
· It enables precise adjustment of the auxiliary frequency and frequency synthesis.
· Supports PM motor (Z2000T series)
· Optional inclusion of built-in EMC filter;
· Power range: 110V/220V/380V/415V/440V/480V, ranging from 0.4kW to 450kW.
Technical Specification:
| Item | Z2000 series |
| Control Mode | Sensorless flux vector control(SFVC) Voltage/Frequency (V/F) Control |
| Maximum frequency | Vector control:0-320Hz V/F control:0-3200Hz |
| Carrier frequency | 1kHz~16kHz The carrier frequency is automatically adjusted based on the load features. |
| Input frequency resolution | Digital setting:0.01Hz Analog setting: Maximum frequency 0.025% |
| Start torque | G: Type:0.5Hz/150%(SVC) P: Type:0.5Hz/100% |
| Speed range | 1:100(SVC) |
| Speed stability accuracy | ±0.5%(SVC) |
| Overload capacity | G Type:60s for 150% of the rated current, 3s for 180% of the rated current. P Type:60s for 120% of the rated current, 3s for 150% of the rated current. |
| Torque boost | Auto-boost ; Customized boost:0.1%~30.0% |
| VF curve | Line V/F curve；Multi-point V/F curve；N-power V/F curve |
| VF separation | 2 types: complete separation；half separation |
| Ramp Mode | Straight-line ramp；S-curve ramp；Four groups of acceleration/deceleration time:0~6500.0s |
| Auto voltage regulation(AVR) | It can keep constant output voltage automatically when the mains voltage changes |
| Rapid current limit | It helps to avoid frequent over current faults of the AC drive. |
| Torque limit and control | It can keep constant output voltage automatically when the mains voltage changes |
| Onboard PID | It realizes process-controlled closed loop control system easily |
| JOG control | JOG frequency range: 0.00–50.00 Hz JOG acceleration/deceleration time: 0.0–6500.0s |
| DC braking | DC braking frequency:0.00Hz to maximum frequency Braking time:0.0-100.0s Braking action current value:0.0%-100.0% |
| Instantaneous blackout doesn’t stop | The load feedback energy compensates the voltage reduction so that the AC drive can continue to run for a short time. |
| Timing control | Timing range:0.0Min~6500.0Min |
| Communication | RS485 / Ethecat(optional) |
| Run command channel | Given by the panel,control terminals,serial communication port,can be switched by many ways |
| Frequency source | 10 kinds of frequency source, given by digital analog voltage, analog current, pulse, serial port. It can be switched by many ways |
| Auxiliary frequency source | 10 kinds of frequency source, can easily realize micro adjustment, frequency Synthesizer |
| Input terminals | 6 digital input terminals, one of which supports up to100 kHz high-speed pulse input (optional). 2 analog input terminal, one of which only supports0-10 V voltage input and the other supports 0-10V voltage input or 4-20 mA current input. |
| Output terminals | 1 digital output terminal 1 relay output terminal 1 analog output terminal: that supports 0-20 mA current output or 0-10v voltage output |
| Multiple protection modes | Motor short-circuit detection at power-on, output phase loss protection, over-current protection, over-voltage protection, under voltage protection, overheat protection and overload protection. |
Product configuration Z2000:
| Close loop vector control | No |
| Built-in braking unit | Yes,below 37kw (include 37kw). Optional for more than 45KW |
| VF+Vector control | Yes |
| High speed pulse output | Yes |
| Movable digital keypad | Yes |
| AI | 2 |
| AO | 1 |
| DI | 6 |
| DO | Standard 1,optional 2 |
| Relay output | Standard 1,over 30kw optional 2 |
| DC braking | Yes |
| Collector | 1 |
| 24V power supply | Below 30kw optional,30kw and above support |
| EMC filter | Optional |
| 0.1S acceleration/deceleration | Yes |
| Simple PLC | Yes |
| All kinds of protection | Support |
| PID | Yes |
| DC choke | 30kw—220kw optional,250kw and above all have |
| DC bus +,- terminals | Yes |
| STO function | No |
| Communication | RS485 |
| Certificate | KC+CE |
| Warranty | 18 months |
Product wiring diagram:
Product specification:
About our company:
ZONCN has 6 main series of VFDs: NZ100, NZ200, Z2000, Z8000, T8000D, H5000BF, and H5000. Besides we also have servo system and electrical vehicle driver and some specially designed products. The voltage ranges are from 110V to 1140V; power range covers 0.4kW to 1000Kw. Our products are widely used in textile, print, CNC machine, food package, injection machine, fan, pump, air compressor, water treatment, industrial washing machine and many industrial applications.
ZONCN has more than 80 dealers in china and abroad. Now our products are exported to more than 50 countries in Asia, Europe, Africa and America. ZONCN will always dedicate in the field of electrical drive and warmly welcome you to be our partner.
FAQ:
Q1:What is your MOQ?
A: 1 pc
Q2:What's your terms of payment?
A:T/T 100% before delivery.
Q3:What's your delivery time?
A:Generally within 15 days after receiving full payment.
Q4:How can l get OEM/ODM order?
A:If your order quantity meets certain requirements, we are happy to customize it for you. We have cooperation with more than forty manufacturers.
Product Tags:
|
|
5.5KW Single Phase Motor Vfd 380v Senseless Flux Vector Control Images
|
